1
|
The toilet is
of the standard zero-gravity type. Depending on requirements, system A
and/or system B can be used, details of which are clearly marked in the
toilet compartment. When operating system A, depress lever and a plastic
dalkron eliminator will be dispensed through the slot immediately
underneath. When you have fastened the adhesive lip, attach connection
marked by the large "X" outlet hose. Twist the silver coloured ring one
inch below the connection point until you feel it
lock.
|
2
|
The toilet is
now ready for use. The Sonovac cleanser is activated by the small switch
on the lip. When securing, twist the ring back to its initial-condition,
so that the two orange lines meet. Disconnect. Place the dalkron
eliminator in the vacuum receptacle to the rear. Activate by pressing the
blue button.
|
3
|
The controls
for system B are located on the opposite wall. The red release switch
places the uroliminator into position; it can be adjusted manually up or
down by pressing the blue manual release button. The opening is self
adjusting. To secure after use, press the green button which
simultaneously activates the evaporator and returns the uroliminator to
its storage position.
|
4
|
You may leave
the lavatory if the green exit light is on over the door. If the red light
is illuminated, one of the lavatory facilities is not properly secured.
Press the "Stewardess" call button to the right of the door. She will
secure all facilities from her control panel outside. When green exit
light goes on you may open the door and leave. Please close door behind
you.
|
5
|
To use the
Sonoshower, first undress and place all your clothes in the clothes rack.
Put on the velcro slippers located in the cabinet immediately below. Enter
the shower. On the control panel to your upper right upon entering you
will see a "Shower seal" button. Press to activate. A green light will
then be illuminated immediately below. On the intensity knob select the
desired setting. Now depress the Sonovac activation lever. Bathe
normally.
|
6
|
The Sonovac
will automatically go off after three minutes unless you activate the
"Manual off" over-ride switch by flipping it up. When you are ready to
leave, press the blue "Shower seal" release button. The door will open and
you may leave. Please remove the velcro slippers and place them in their
container.
|
7
|
If the red
light above this panel is on, the toilet is in use. When the green light
is illuminated you may enter. however, you must carefully follow all
instructions when using the facilities during coasting (Zero G) flight.
Inside there are three facilities: (1) the Sonowasher, (2) the Sonoshower,
(3) the toilet. All three are designed to be used under weightless
conditions. Please observe the sequence of operations for each individual
facility.
|
8
|
Two modes for
Sonowashing your face and hands are available, the "moist-towel" mode and
the "Sonovac" ultrasonic cleaner mode. You may select either mode by
moving the appropriate lever to the "Activate" position.
If you choose the
"moist-towel" mode, depress the indicated yellow button and withdraw item.
When you have finished, discard the towel in the vacuum dispenser, holding
the indicated lever in an "active" position until the green light goes on
. . . showing that the rollers have passed the towel completely into the
dispenser. If you desire an additional towel, press the yellow button and
repeat the cycle.
|
9
|
If you prefer
the "Sonovac" ultrasonic cleaning mode, press the indicated blue button.
When the twin panels open, pull forward by rings A and B. For cleaning the
hands, use in this position. Set the timer to positions 10, 20, 30 or 40 .
. . indicative of the number of seconds required. The knob to the left,
just below the blue light, has three settings, low, medium or high. For
normal use, the medium setting is suggested.
|
10 |
After these
settings have been made, you can activate the device by switching to the
"ON" position the clearly marked red switch. If, during the washing
operation, you wish to change the settings, place the "manual off"
override switch in the "OFF" position. You may now make the change and
repeat the cycle.
|